How to Flash Stock Rom on Samsung Galaxy J9 2018 Pro MT6580
Flash Stock Firmware on Samsung Galaxy J9 2018 Pro MT6580: We use the SP Flash tool but we also give you all possible and available Flashing methods and all available Stock firmware to Flash Stock Rom on Samsung Galaxy J9 2018 Pro MT6580. Don’t worry If you really want to Flash a Rom to Unbrick, Rollback, Repair, unroot, full system restore then you are in the right website. so Flash it. as well, below the guide, we discuss errors of flashing Custom / Stock Rom and we offer you possible solutions for those errors. Note– What is the Stock & Custom Rom? Firmware? Bootloader?
you should know these things
♥ You can do this if you want to Go back to Official Stock Rom or reinstall Stock firmware.
♥ phone’s pc software does not want to install but the phone driver must works on PC without error.
♥ This Stock Rom has to be installed on this model only.
♥ Do this your own risk, If you do any wrong then the phone will be damaged. If so, try again or contact us.
♥ SP Flash tool works on MTK Device only.. you had better check it first..
♥ If you want to upgrade your Samsung Galaxy J9 2018 Pro MT6580 then you have to find upgraded Rom – KitKat, Lollipop, Marshmallow, Nougat, Oreo, Pie. we provide only Official Rom
How to Install Stock ROM on Samsung Galaxy J9 2018 Pro MT6580
The requirement for Flashing Official Firmware/ ROM
Step 1, (Optional)
Enable “Developer and Debugging mode“
Turn off your Samsung Galaxy J9 2018 Pro MT6580 Device by pressing the Power button.
Download Stock Rom For Samsung Galaxy J9 2018 Pro MT6580.
Download Samsung Galaxy J9 2018 Pro MT6580. Stock Rom (please Find right Stock Rom)
After the open Flash tool. There is a tab called Download. Click the “Download tab”
after that, There is a button Called “Scatter-Loading”. Click it and locate the scatter file. there is the scatter file in the Stock Rom folder. something like – “#### android scatter.txt”
Start Flashing Stock Rom on Samsung Galaxy J9 2018 Pro MT6580.
Final Step. Click the Download button to Begin Flash.
Now connect your Samsung Galaxy J9 2018 Pro MT6580 Device to your PC or lap via data cable. after then, press Volume Up and Volume Down until the Samsung Galaxy J9 2018 Pro MT6580 Device is detected by your PC. (without battery). after the complete Flashing process, the SP Flash tool indicates green right.
Now disconnect your phone from PC and insert the battery and switch on the phone. Congratulations, Now you successfully installed Stock Rom.
Errors and Solutions
Samsung Galaxy J9 2018 Pro MT6580 phone not works after flashing
A : Give it to 5min. because first boot is slow. If not works, then flash it again please go step by step.
Samsung Galaxy J9 2018 Pro MT6580. stuck at Boot logo or Bootloop
A: Git it to 5min because first boot is Slow. Remove the battery for 60 seconds then insert back. If not works then boot into recovery mode and wipe the data (Hard reset). If not works then Try again to install Stock Rom.
automatically disconnecting during flashing Samsung Galaxy J9 2018 Pro MT6580 phone
- please Try another data cable.
- Try to install Drivers again
- Try another Computer.
I can’t Flash Stock Rom Samsung Galaxy J9 2018 Pro MT6580 phone
please try again. after did, if does not works then leave a comment with an error message. you Had better give us a Screenshot.
My Samsung Galaxy J9 2018 Pro MT6580 phone keep restarting
- It may be your Samsung Galaxy J9 2018 Pro MT6580. the case is pressing on it
- Maybe, your current Rom is Corrupted or damaged. So you have to Install Stock Rom to ON your phone. use this post to Flash new Stock Rom. If you can, use different Rom.
- Try to format your phone using Sp flash tool,
- Find another Rom
- If not works, then open the Scatter file using windows Notepad+ and try to change __NODL_FAT to FAT by removing “__NODL_”
Other error messages and Solutions ..
- Below we listed errors of SP Flash tool and there is a link to fix these errors. Phone shows white screen,Sp Flash tool remains at 0%,Error 5054,Initialize Scatter failed,Error 0X411,
8038! Android download pmt is ready and layout has been changedLED
BROM ERROR : S_FT_DOWNLOAD_FAIL (4008) - this is a encountered an error.
BROM ERROR : S_DA_SDMMC_WRITE_FAILED (3149) Sp can't Flash files. go to dedicated post below
BROM ERROR: S_CHIP_TYRE_NOT_MATCH(3168)
ROM ERROR S_DL_GET_DRAM_SETTINGS_FAIL (5054) go to dedicated post below
BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) [EMI] Enable DRAM fail
BROM ERROR : S_FTHND_FILE_IS_NOT_LOADED_YET (5007) go to dedicated post below
BROM ERROR: S_STORAGE_NOT_MATCH (3182) visit dedicated post below
BROM ERROR: S_SECURITY_SF_CODE_COMMAND_FORBIDDEN (6012), MSP ERROR CODE: 0X00
If you face this kind of error message then this is the face for fix it. Go to this dedicated post
So, If this Samsung Galaxy J9 2018 Pro MT6580 phone Flashing guide line helped, then please share this guideline to Facebook and Twitter. Help others to find out this guideline on Facebook. If you have any doubt or any problem, don’t hesitate, feel free to reply. After then we are able to help you as well as be sure to bookmark our site on your browser.