Flash Stock Rom on QMobile Noir A120
We use SP Flash tool but we also give you all possible and available Flashing methods and all available Stock firmware to your QMobile Noir A120. Don’t worry If you really want to Flash a Rom to Unbrick,Rollback, Repair, unroot, then you are in right website. so Flash it. as wel, below the guide, we discuss about errors of flashing Custom/Stock Rom and we offer you possible solutions for those errors.
you should know these things
♥ You can do this if you want Go back to Official Stock Rom or reinstall Stock firmware.
♥ phone’s pc software does not want to install but phone driver must works on PC without error.
♥ This Stock Rom has to be installed on this model only.
♥ Do this your own risk, If you do any wrong then phone will be damaged. If so, try again or contact us.
♥ SP Flash tool works MTK Device only.. you had better check it first..
♥ If you want to upgrade your QMobile Noir A120 then you have to find upgraded Rom – marshmallow, kitkat .we provide only Official Rom
Install Stock Rom on QMobile Noir A120
Requirement for Flashing Official Firmware/ ROM
Note – we recommend you to get full backup before doing this.
Download and install QMobile Noir A120 USB drivers
Turn off your Qmobile phone phone by pressing Power button and remove the battery.
Download Official Stock Rom For QMobile Noir A120
Download QMobile Noir A120 Stock Rom (please Find right Stock Rom)
After open Flash tool. There is tab called Download. Click the “Download tab”
after that, There is a button Called “Scatter-Loading”. Click it and locate the catter file. there is the catter file in the Stock Rom folder. some thing like – “#### android catter.txt”
Start Flashing Stock Rom on QMobile Noir A120
Final Step. Click the Download button to Begin Flash.
Now connect your Qmobile phone phone to your PC or lap via data cable. after then, press Volume Up and Volume Down until the Qmobile phone phone is detected by your PC. (without battery). after complete Flashing process, SP Flash tool indicate green right.
Now disconnect your phone from PC and insert the battery and switch on the phone. Congratulations, Now you successfully installed Stock Rom.
Errors and Solutions
Qmobile phone not works after flashing
A : Give it to 5min. because first boot is slow. If not works, then flash it again.
QMobile Noir A120 stuck at Boot logo or Bootloop
A: Git it to 5min because first boot is Slow. Remove the battery for 60 seconds then insert back. If not works then boot into recovery mood and wipe the data. If not works then Try again to install Stock Rom.
automatically disconnecting during flashing Qmobile phone
Try another data cable.
Try to install Drivers again
I can’t Flash Stock Rom Qmobile phone
please try again. after did, if does not works then leave a comment with error message. Had better give us Screenshot.
My phone keep restarting
- It may be your QMobile Noir A120 case is pressing on it
- May be, your current Rom is Corrupted or damaged. So you have to Install Stock Rom to ON your phone. use this post to Flash new Stock Rom. If you can, use different Rom.
- Try to format your phone using Sp flash tool,
- Find another Rom
- If not works, then open the scatter file using windows Notepad+ and try to change __NODL_FAT to FAT by removing “__NODL_”
Other error messages and Solutions ..
Below we listed errors of SP Flash tool and there is a link to fix these errors. Phone shows white screen,Sp Flash tool remains at 0%,Error 5054,Initialize scatter failed,Error 0X411,
8038! Android download pmt is ready and layout has been changedLED
BROM ERROR : S_FT_DOWNLOAD_FAIL (4008)
BROM ERROR : S_DA_SDMMC_WRITE_FAILED (3149)
BROM ERROR: S_CHIP_TYRE_NOT_MATCH(3168)
ROM ERROR S_DL_GET_DRAM_SETTINGS_FAIL (5054)
BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) [EMI] Enable DRAM fail
BROM ERROR : S_DL_PMT_ERR_NO_SPACE (5069)
BROM ERROR : S_FT_DA_NO_RESPONSE (0xFA1)
BROM ERROR:S_COM_PORT_OPEN Fail(1013)
BROM ERROR : S_FTHND_FILE_IS_NOT_LOADED_YET (5007),
BROM ERROR: S_STORAGE_NOT_MATCH (3182),
BROM ERROR: S_SECURITY_SF_CODE_COMMAND_FORBIDDEN (6012), MSP ERROR CODE: 0X00,
BROM ERROR: S_TIMEOUT (1042)
If you face this kind of error message then this is the place for fix it. Go to this dedicated post
So, If this Qmobile phone Flashing guide line was help, then please share this guide line to Facebook and twitter. Help others to find out this guide line on Facebook. If you have an any doubt or any problem, don’t hesitate feel free to reply. After then we are able to help you as well as be sure to bookmark our site on your browser.